The original sketch was done in 3D Studio Max. We found a few references of desks that she liked and then I took some liberties putting something together. She helped make some decisions along the way, but this is what we came up with:

And cutting begins… Organizing various pieces:

I love using pocket holes to build face frames. They’re efficient and end up creating a really strong joint:

The two sets of carcasses for the drawers:

One of the drawers:

For the drawer faces I used a 1/2″ roundover bit to route the edges:

Drawers coming together. I’m using a single guide below each drawer that has a C bracket to help it slide. They sit on that and the face frame rails. I used flat thumbtacks at either corner of the rails so the drawers slide a bit smoother.

Both sets are complete:

The top of the desk is made of 4 1×5 planks that I edge joined using pocket hole screws and glue. This was the first time I’ve attempted to edge join boards.

Lots of sanding to get rid of those high spots:

I don’t have many pictures of the hutch construction so here’s a detail of one of the small drawers and then the completed unit:

And finally the completed desk assembly. The plan is to stain the desk top, and paint the rest of it an off-white. The drawer knobs will be stained to match the top.

Then moved onto the chair… The plans call for starting with the seat assembly, attaching the lower back rail first and squaring everything up, then adding one of the front slats, and filling in from there. Attaching the front legs was a bit tricky because you have to get them positioned just right in order for the seat to be properly angled. After that I moved to the back, attaching the back legs and the top back rail. Back slats were next, followed up by the arms.

Everything was put together with 2″ deck screws that I pre-drilled and countersunk – though on a couple places of the chair I still had some issue with the wood splitting. A little water resistant Gorilla Glue and a couple clamps should do the trick…

And the finished product… The seat curve feels just right and the angle of the back slats is perfect. I’m also loving the seat height – it’s a little lower than your typical lawn chair. I’m definitely going to be making a another one to create a pair. Something tells me these are going to get a lot of use…

Picked it up at the Woodcraft in Allentown. I love that store… I could spend an hour just staring at all the woodworking supplies they have lining the aisles. They have a rather impressive section of Festool tools as well, but I need a hell of a lot more disposable income to afford that stuff.

I also cut the tapers necessary for the back slats of the chair – those were a pain. I have a taper jig for my table saw but the stock for the back slats was just too long for it. I couldn’t figure out a good way to cut them so in the end I just eyeballed it on the table saw, following the lines I had marked – not perfect, but it got done. After cutting those, I laid them out on the floor and marked a line for the curve at the top, then used the jigsaw to cut that as well.

What really saved me time was this software.  It automatically figures out the best arrangement of material pieces from a given set of stock. All you have to do is plug in the numbers and it does all the rest. This is the cut diagram it gave me based on using 9 pieces of 1x6x8 cedar boards:

As you can see, it would’ve taken forever to figure that all out by hand.

I’m also trying something different for keeping track of all the boards; I’m using little stickers with letters on them corresponding with the materials list from the original plans. This is in place of writing directly on the boards which I would’ve had to sand off later.

Basic stuff here… 1/2″ plywood for the main carcass. And I ripped down some pine into 1×2′s and 1×3′s for the face frame, putting it together with pocket screws first, then tacking it to the front of the piece.

The initial sketch:

A clay rendering in Max:

The finished piece:

And in use:

A closeup of the headboard design:

The extended trundle:

A detail of the arched design in the footboard that I carried through to the trundle:

The distressed finish I used throughout the piece: